Setting beberapa jenis modem yang digunakan untuk layanan Telkom Speedy, berikut adalah setting dari beberapa jenis modem ADSL yang biasa digunakan untuk warnet

Adsl Modem SMC

Default IP: 192.168.2.1
Default password: smcadmin

Setting Bridge:

- Klik WAN

- Clik ATM PVC

- Klik VCI

- Protocol: 1483 Bridging, VLAN: Default, VPI/VCI: 8/81, Encapsulation: LLC, Qos Class: UBR, PCR/SCR/MBS: 4000/4000/10

- Klik Save Settings

Setting PPPoE:

- Klik WAN

- Klik ATM PVC

- Klik VCI

- Protocol: PPPoE, VPI/VCI: 8/81, Encapsulation: LLC, QoS Class: UBR, PCR/SCR/MBS: 4000/4000/10, IP assigned by ISP: Yes, IP Address: 0.0.0.0, Subnet Mask: 0.0.0.0, Connect Type: Always Connected, Idle Time (Minute): 5, Username: This e-mail address is being protected from spambots. You need JavaScript enabled to view it , Password: (password dari telkom), Confirm Password: , MTU: 1492

- Save Settings

Adsl Modem ZyXeL

P-660R

Default IP: 192.168.1.1
Default username: admin
Default password: 1234

Setting Bridge

- Pilih Network

- Pilih WAN

- Mode: Bridge, Encapsulation: RFC 1483, Multiplexing: LLC, VPI: 8, VCI: 81, Apply

- Pilih Maintenance

- Pilih Tools

- Restart

Setting PPPoE

- Pilih Network

- Pilih WAN

- Mode: Routing, Encapsulation: PPPoE, Username: ( This e-mail address is being protected from spambots. You need JavaScript enabled to view it ), Password: (password speedy), Service Name: Speedy, Multiplexing: LLC, VPI: 8, VCI: 81, IP Address: Obtain an IP Address Automatically, Connection: Nailed-Up Connnection, Apply

- Klik Maintenance

- Klik Tools

- Restart

Adsl Modem Shiro

Default IP: 192.168.1.1
Default username: admin
Default password: admin

Setting Bridge:

- Klik Advanced

- Klik WAN

- Klik New Connection

- Connection Name: Speedy, Type: Bridge, VPI: 8, VCI: 81, and Submit

- Save Settings

- Restart Router

Setting PPPoE:

- Pilih Advanced

- Pilih WAN

- Klik New Connection

- Connection Name: Speedy, Type: PPPoE, Sharing: Enable, Encapsulation: LLC, Username: This e-mail address is being protected from spambots. You need JavaScript enabled to view it , Password: (password dari telkom), VPI: 8, VCI: 81, and Submit

- Save Settings

- Restart Router

Adsl Modem Aztech

Default IP: 192.168.1.1
Default username: admin
Default password: admin

Setting Bridge:

- Klik Advanced

- Klik WAN

- Klik New Connection

- Connection Name: Speedy, Type: Bridge, VPI: 8, VCI: 81, and Submit.

- Save Settings

- Restart Router

Setting PPPoE/Router:

- Klik Advanced

- Klik WAN

- Klik New Connection

- Connection Name: Speedy, Type: PPPoE, Sharing: Enable, Encapsulation: LLC, Username: This e-mail address is being protected from spambots. You need JavaScript enabled to view it , Password: (password dari telkom), VPI: 8, VCI: 81, and Submit.

- Save Settings

- Restart Router

Adsl Modem TECOM

AR1031

Default ip: 192.168.1.1
Default username: admin
Default password: admin

Setting Bridge:

- Klik Advanced Setup

- Klik WAN

- Klik Edit

- ATM PVC Configuration, VPI=8; VCI=81, Service Category: UBR Without PCR, Next

- Connection Type Bridging, Encapsulation Mode LLC/SNAP-BRIDGING, Next

- Cheklist Enable Bridge Service, Service Name: Speedy, Next

- WAN Setup - Summary, Save

- Save/Reboot

Setting PPPoE:

- Klik Advanced Setup

- Klik WAN

- Klik Edit

- ATM PVC Configuration, VPI=8; VCI=81, Service Category: UBR Without PCR, Next

- Connection Type PPP over Ethernet (PPPoE), Encapsulation Mode LLC/SNAP-BRIDGING, Next

- Put your PPP Username: This e-mail address is being protected from spambots. You need JavaScript enabled to view it ; PPP Password: (password dari telkom); PPPoE Service Name: Speedy, Next

- Cheklist Enable WAN Service, Service Name: Speedy, Next

- WAN Setup - Summary, Save

- Save/Reboot

Adsl Modem Billion

Setting:

- Login To: http://192.168.1.254

- User name = admin; Password = password dari telkom

- Klik -> OK

- Klik: Quick Start

- Edit Connection:
Encapsulation = PPPoE LLC
Bridge = Enabled
Setting VPI = 8 dan VCI = 81 , and Than
Static IP Setting
IP Address = 0.0.0.0
subnet mask = 0.0.0.0
Gateway = 0.0.0.0

- Klik: - Submit
- SAVE CONFIG

- Klik: Submit

- Wait Till process Configuration done !

- Configuration Done !

Modem Prolink

- Login To -> http:// 10.0.0.2
User Name: admin
Password: password
Klik . . . . OK

- Chose Configurasi WAN:

- Select Adapter: Pilih Pvc3 (Indonesia)

- Edit Field:
Bridge = Enable
Encapsulation = 1483 Bridge IP LLC
ATM VPI = 8
ATM VCI = 81



 

-  Static IP Setting: “ just blank “
IP Address = just empty
Subnet Mask = just empty
Gateway = just empty
User Name = This e-mail address is being protected from spambots. You need JavaScript enabled to view it . . . . . . ( optional ) *
Password = xxxxxxxx . . . . . . . . . . . . . . . . . . .( optional ) *
* If you choose to put username & password there just double clik explorer
* If you not choose to put username & password there you have to create new connection at Network Connection

- Create New Connection (Bridge) See here..>>

- Than Next:

- * Klik Submit

- * Klik Save Configuration

- Next: Save Reboot ….

Adsl Modem D-Link

DSL-302T

Default IP: 192.168.1.1
Default username: admin
Default password: admin

Setting Bridge:

- Klik Setup

- Klik Connection

- Bridge Connection Setup. Name: Speedy; Type: Bridge; Encapsulation: LLC; VPI=8; VCI=81, Apply

- Klik Tools

- Klik System Commands, Save All, Restart

Setting PPPoE/Router:

- Klik Setup

- Klik Connection

- Bridge Connection Setup. Name: Speedy; Type: PPPoE; Username: This e-mail address is being protected from spambots. You need JavaScript enabled to view it ; Password: (password dari telkom); VPI=8; VCI=81, Apply

- Klik Tools

- Klik System Commands. Save All, Restart

adsl Modem Repotec

- Buka Internet Explorer ketik: http://192.168.1.1

- Username: admin & Password: epicrouter

- Klik: OK

- Klik WAN

- Pic Adapter: Pvc0

- Klik Submit

- Virtual Circuit = Enabled

- Bridge & IGMP = Disable

- Each region was different from another region and for Bandung vpi:8 , vci: 81

- Service Category = UBR without PCR

- Protocol/Conection type = PPPoE

- Encapsulation = LLC/Snap-Bridging

- Put Username & Password from your provider

- Klik Submit.

- Klik Save Configuration (wait till Saving configuration done.)

- put DNS: 202.134.0.155 & 202.134.2.5

Adsl Modem Dareglobal

Default IP: 192.168.1.1
Default username: admin
Default password: admin

Setting Bridge:

- Klik Advanced Setup

- Klik WAN

- Find VPI/VCI: 8/81, Klik Edit

- ATM PVC Configuration, VPI=8; VCI=81, Service Category: UBR Without PCR, Next

- Connection Type Bridging, Encapsulation Mode LLC/SNAP-BRIDGING, Next

- Cheklist Enable Bridge Service, Service Name: Speedy, Next

- WAN Setup - Summary, Save

- Save/Reboot

Setting PPPoE:

- Klik Advanced Setup

- Klik WAN

- Cari VPI/VCI: 8/81, Klik Edit

- ATM PVC Configuration, VPI=8; VCI=81, Service Category: UBR Without PCR, Next

- Connection Type PPP over Ethernet (PPPoE), Encapsulation Mode LLC/SNAP-BRIDGING, Next

- Put your PPP Username: This e-mail address is being protected from spambots. You need JavaScript enabled to view it ; PPP Password: (password dari telkom); PPPoE Service Name: Speedy, Next

- Centang Enable WAN Service, Service Name: Speedy, Next

- WAN Setup - Summary, Save

- Save/Reboot

Adsl Modem TP-Link

Default IP: 192.168.1.1
Default username: admin
Default password: admin

Setting Bridge:

- Klik Advanced Setup

- Klik WAN

- Find VPI/VCI: 8/81, Klik Edit

- ATM PVC Configuration, VPI=8; VCI=81, Service Category: UBR Without PCR, Next

- Connection Type Bridging, Encapsulation Mode LLC/SNAP-BRIDGING, Next

- Cheklist Enable Bridge Service, Service Name: Speedy, Next

- WAN Setup - Summary, Save

- Save/Reboot

Setting PPPoE:

- Klik Advanced Setup

- Klik WAN

- Find VPI/VCI: 8/81, Klik Edit

- ATM PVC Configuration, VPI=8; VCI=81, Service Category: UBR Without PCR, Next

- Connection Type PPP over Ethernet (PPPoE), Encapsulation Mode LLC/SNAP-BRIDGING, Next

- Put your PPP Username: This e-mail address is being protected from spambots. You need JavaScript enabled to view it ; PPP Password: (password dari telkom); PPPoE Service Name: Speedy, Next

- Cheklist Enable WAN Service, Service Name: Speedy, Next

- WAN Setup - Summary, Save

- Save/Reboot

Setting Modem Articonet ACN-100R dan ACN-110

Cara melakukan setting di komputer untuk akses ke modem Articonet.
Untuk setting di komputer dilakukan sesuai dengan operating system yang dipakai di komputer pelanggan, disini yang dibahas khusus untuk Windows XP.
Lakukan network setting di PC (komputer) sbb:

a. Start – Control Panel – Network Connection
b. arahkan kursor pada Local Area Connection yang aktif, kemudian klik kanan dan pilih properties
c. kemudian pilih menu Internet Protocol (TCP/IP) dan klik 2X, maka akan muncul menu General.
d. Pilih Obtain an IP Address Automatically kemudian pilih Obtain DNS server address automatically, kemudian tekan tombol OK.

Panduan cara setting modem ADSL Speedy koneksi PPPoE.(PPPoE)
Setting modem dilakukan melalui browser dengan mengakses alamat http://192.168.1.1
Masukkan username dan password: admin/admin
Setelah masuk ke menu setting lakukan langkah berikut:
Masuk ke menu "Advanced Setup" kemudian pilih "WAN" dan klik tombol "Edit" disebelah kanan tabel WAN Masukkan nilai PVC Configuration: (masukkan nilainya sesuai wilayah TELKOM masing-masing daerah)
VPI = X
VCI = XX
Service Category = UBR Without PCR, kemudian klik tombol Next
Connection type = PPPoE
Encapsulation = LLC, kemudian klik tombol Next
Masukkan username dan password Speedy, kemudian klik tombol Next
Tandai atau kasih v untuk pilihan "Enable WAN Service", kemudian klik Next dan klik tombol Save
Setting PPPoE untuk koneksi Speedy telah selesai dilakukan
Selanjutnya klik tombol Save/Reboot
(Modem akan reboot -/+1 menit dan tunggu sampai modem normal kembali)

Berikut langkah setting modem ADSL Articonet untuk Dial-Up/Bridge.
Setting modem dilakukan melalui browser dengan mengakses alamat http://192.168.1.1
Masukkan username dan password: admin/admin
Setelah masuk ke menu setting lakukan langkah berikut:
Masuk ke menu "Advanced Setup" kemudian pilih "WAN" dan klik tombol "Edit" Masukkan nilai PVC Configuration: (masukkan nilainya sesuai wilayah TELKOM masing-masing daerah)
VPI = X
VCI = XX
Service Category = UBR Without PCR, kemudian klik tombol Next
Connection type = Bridging
Encapsulation = LLC, kemudian klik tombol Next
Tandai atau kasih v untuk pilihan "Enable Bridge Service", kemudian klik Next dan klik tombol Save
Setting Bridge untuk koneksi Speedy telah selesai dilakukan
Selanjutnya klik tombol Save/Reboot
(Modem akan reboot -/+1 menit dan tunggu sampai modem normal kembali)

Setting modem Articonet untuk koneksi Bridging sudah selesai, langkah berikutnya setting koneksi Dial-Up di PC/komputer.

Panduan instalasi Dial Up koneksi ADSL menggunakan Windows 2000:

- Klik Start, klik Setting,klik Control Panel,

- Klik Network and Dial Up Connections.

- Klik Make New Connection, klik Next,

- Klik Dial Up to the Internet

- Klik I want to setup my internet manually, klik Next

- Klik I connect through a phone line and a modem klik Next

- Pilih dan klik modem ADSL yang sesuai

- Isi username: This e-mail address is being protected from spambots. You need JavaScript enabled to view it

- Password: xxxxxxxx

- Klik OK dan Lanjutkan sesuai perintah yang muncul

- Klik Finish

Panduan installasi Dial Up koneksi ADSL menggunakan Windows Xp:

- Klik Start, klik Setting, klik Control Panel.

- Klik Network Connection

- Klik Create a New Connection, klik Next.

- Klik Connect to the Internet, klik Next

- Klik Setup my connection manually, klik Next

- Klik Connect Using Dial Up, klik Next

- Klik modem ADSL yang sesuai, klik Next

- Isi username: This e-mail address is being protected from spambots. You need JavaScript enabled to view it dan Password: *******

- Confirm password: xxxxxxxx

- kemudian beri tanda v pada pilihan "Add a shortcut to the desktop screen"

- Klik Finish